cre.ations.net

Comment on Create your own noise blocking in-ear headphones by natetrue

Mon, 25 May 2009 09:00:07 -0500

At 25-May-2009 09:00:07, natetrue posted:

Those look great, anneruns. I love the colors and designs!

Comment on Create your own noise blocking in-ear headphones by anneruns

Sun, 10 May 2009 20:11:42 -0500

At 10-May-2009 20:11:42, anneruns posted:

okay, here is the picture that i meant to attach on previous comment...
1st - (not shown, bc it didn't turn out well)
2nd - silver w/ tad blue tint and a yellow smilie face
3rd - blue with tiny green polka dots
4th - blue/green/white swirly tie-die look

fyi- i had no danger with ear canal because both of my ear canals were sewn closed off after i had surgeries to remove tumors on auditory nerves. so the ear goes in about half an inch, then it ends. if ur ear is like normal, this activity can be very dangerous... so, its probably still best to have a professional do it.

i still have to do the drill part for small tube that ataches to the implant. i dont have drill here but know where i can use one.

homework time!!

Comment on Create your own noise blocking in-ear headphones by anneruns

Sun, 10 May 2009 20:03:24 -0500

At 10-May-2009 20:03:24, anneruns posted:

I joined this site just say thank you and this was pretty awesome project! ....geee, i should be doing homework!! I did it a little differently. I recently became deaf, because i had tumors on my auditory nerves... so in-ear-noise-blocking-headphones won't do me any good.... I used a putty epoxy that sets a bit faster and it was cheaper too ($5 at Lowe's) to make an ear-mold for my Auditory Brain-stem Implant. (similar to a cochlear implant) that is different from a hearing aid, so basically the optional earmold attachment is to make it feel more secure and not be paranoid about the $6,000 sound processor falling off the side of my head! like you said, I can get a custom ear-mold made for around 50 to 100 dollars, but this was a fun! haha. i made 4 of them!! the first turned out like hell, but the rest look really cool. i made them all on the same ear, because i have one implant, and my other ear is useless ....other than for holding up sunglasses! I also made them in different colors with paints and dyes, stuff i already had since i am an art student.

Comment on Create your own noise blocking in-ear headphones by fastass

Mon, 06 Apr 2009 11:08:03 -0500

At 06-Apr-2009 11:08:03, fastass posted:

Hi Yes 100g of it will be plenty, also if you make a mistake you can remelt it as many times as u want :).
If you need any help just ask :))

Comment on Create your own noise blocking in-ear headphones by frantab

Sun, 05 Apr 2009 14:50:26 -0500

At 05-Apr-2009 14:50:26, frantab posted:

Hi, I´m going to make them from Polymorph, but my question is, how many of Polymorph did you use. If I buy 100g of it, will it be enough for both molds?

Comment on Create your own noise blocking in-ear headphones by panther

Fri, 23 Jan 2009 15:01:41 -0600

At 23-Jan-2009 15:01:41, panther posted:

Me again. I tried this again, this time, buying a pair of Philips Surround SHE5920 earbuds. They costed $15.60 with tax at WalMart. Despite great reviews online, I found these earbuds lacked bass and sounded "tinny". Honestly my iPod stock earbuds sound better. Anyway, I made them into custom-fitted earphones as above. I recommend mixing a little paint with the epoxy so it's colored evenly throughout. Also, I did my "wax dipping" in a mug, instead on using tea lights. No picture this time because they look almost the same as my previous pair!

Comment on Create your own noise blocking in-ear headphones by willchamber

Wed, 21 Jan 2009 20:09:38 -0600

At 21-Jan-2009 20:09:38, willchamber posted:

Signed up to this site just so I could give you all a massive thankyou!! Used both the original and "fastass's" methods, and have one amazing set of earphones! Put cx300's in the polymorph mold and sealed it all up and smoothed away. A soldering did most of the work heating and scooping the area for the buds. Then I used it to seal it up by hearing strips real hot and layering them around them. Sound isolation improved and no lack of quality! SO much more comfortable now, with them now being over ear. A few coats of blue metallic paint and it's done! If I can get to a camera I'll post some pictures. Once a massive thankyou for giving me confidence to try this! Peace x

Comment on Create your own noise blocking in-ear headphones by panther

Sat, 17 Jan 2009 22:38:37 -0600

At 17-Jan-2009 22:38:37, panther posted:

I tried making my own earbuds using this as a guide. Some of the things I did differently, and I think it worked well. I went to Lowe's and bought Elmer's 2-part epoxy ($19). I found it took a long time (about 3 hours) for the epoxy to get the consistency of chewing gum. I lined my ears with vaseline, to prevent them from sticking too much to my skin. I formed the epoxy into a "U" shapes, and wrapped it around the earbuds. Then I carefully put them into my ears, making sure the earbuds were blocking my ear canal. I stuffed the rest of the epoxy in around them, making a good fit. This I did in front of a mirror, to make sure it looked okay. I kept a small piece in a ziplock bag to test how hard the stuff was getting. Meanwhile, I listened to music through them, to make sure the earbud was positioned nicely. It took over an hour to get it thick enough to remove (like bubble gum you left on your bedpost overnight).

This method is great because it requires *no drilling!*. Also, it helps ensure the earbud is positioned exactly where you want it in your ear.

After, tried wearing them. They're really uncomfortable unless you do some sanding - so I did. In fact, my left ear got a small cut from it rubbing. I sanded off the hard rough edges. This helped, but still they didn't feel very comfortable. I bought some shiny green paint, and painted them with 2 coats. I thought this might help the comfort factor. See the pictures below - I think shiny paint makes them look great - like real commercial/professional earphones!

Finally I dipped them in wax as described above. This helped a lot. Unfortunately, one of the earbuds stopped working. I'm not sure if it was the wax-dipping, or the fact that they were old to begin with. Anyway, now that I've practiced, I will try again with new ones. One thing's for certain, they sound 10x better, and never fall out!

I also thought about using a product called "Plasti Dip" (http://www.plastidip.com/). You can find it pretty cheap on ebay. Not sure how well it would work, but might be easier to clean than wax.

Comment on Create your own noise blocking in-ear headphones by ejbragg

Sat, 31 May 2008 14:34:06 -0500

At 31-May-2008 14:34:06, ejbragg posted:

Has anyone tried / thought about using a fast-setting rubber for these earbuds? I went to an audiologist a few years back and had them make me some custom earmolds for "musician's earplugs". They squirted a fast-setting rubber or silicon in my ear. Once it was set, they just pulled it out. At the time, they sent me home and called me back within a couple weeks for the finished product.

I have found something on the web that looks similar and is made for the human body - it sets faster in warm temperatures, slower while you're working with it (keep your finger cold). Because the inside of your head is warm, sliding the rubber into your ear canal will cause it to set up faster - they claim within 5 minutes. Because it's a soft rubber, you can go all the way to the eardrum - and acoustically speaking, you SHOULD, actually, BUT being careful not to exert an uncomfortable pressure. When the mold sets up, you pull it out and snip off the end about 1/8" to 1/4" from the eardrum. Otherwise, wearing them will irritate your eardrums.

The reason for going all the way to your eardrum is that your ear canal works a lot like the inside of a speaker cabinet. If you restrict the canal, but leave a wide opening near the ear drum, that cavity will still resonate at low frequencies. The result is that the music may sound very bass-heavy, not attenuating the low frequencies very well, and yet attenuating the higher frequencies very efficiently. Such causes you to have to equalize the stereo system to compensate. Making the earbud as long as your ear canal reduces the bass resonance and all frequencies outside the earbud are attenuated much more evenly.

Now. As jesse commented earlier, there ARE people whose ear canals may actually be larger near the eardrum than anywhere else. So use caution. I would suggest pulling the first molds of each ear out slightly prematurely, just to check out the shape of the canal and make sure it wasn't too difficult to remove. If all seems well, then you'll have PLENTY left over to do again, several times - even if you order the smallest volume available of this stuff...

http://www.smooth-on.com/bd-update.htm

Comment on Create your own noise blocking in-ear headphones by natetrue

Wed, 23 Apr 2008 07:37:37 -0500

At 23-Apr-2008 07:37:37, natetrue posted:

Glad to see this thread still has some life to it. I still use mine whenever I'm on an airplane or any other time I need to have perfect sound.

Comment on Create your own noise blocking in-ear headphones by backxslash

Tue, 08 Apr 2008 12:07:18 -0500

At 08-Apr-2008 12:07:18, backxslash posted:

Kinda feels like I'm necro'ing this thread, but still:

I finally worked up the nerve to (and cash) to make a pair of these things, and all I can say is that it's the best mistake I've made in a long while. I used putty style epoxy designed for "wood repair" to make the molds, and a spare pair of iPod earbuds. I can't comment on sound quality, but the noise blocking quality it fantastic. I've taken to using the only when I'm studying, or riding my scooter, or when I just want to ignore the world. I don't use them any other time because I can see people talking, but I can't hear them, and it makes me a bit nervous. Not cuz I think they're talking about me, but cuz I think someone might sneak up on me. I think I drilled the holes a bit weird though, cuz the sound through them is a bit treble heavy.

Comment on Create your own noise blocking in-ear headphones by fastass

Sat, 01 Sep 2007 05:18:02 -0500

At 01-Sep-2007 05:18:02, fastass posted:

Hi underclocker, This website has all the details on purchasing Polymorph or in the US its called Freindly Plastic.
http://reprap.org/bin/view/Main/Polymorph
Also there are the instructions for using it. It comes in beads that you put into hot water, I just used the water from a kettle, and this then makes it bond together, you can then squash it by hand , when you put it in your ear it is warm and is not uncomftable, it only takes about 5 mins to set. I do advise putting something in your ear canal tied to some thread, to stop it going too far !!!. I did not do this and as my ear canals are hooked you can imagine how much fun it was to get the mold out !!!!!!
I didnt drill the molds, insted I melted the mold with special adaptors you can get for soldering irons to scoop out where the headphone was to be placed. I then used a spare bike wheel spoke !!!, heated up to make a nice clean hole for the sound to travel down the ear canal part.
I supose its finding a way you find easiest, it took me several attempts toget the method right but its worth it :)

Comment on Create your own noise blocking in-ear headphones by underclocker

Fri, 31 Aug 2007 22:13:46 -0500

At 31-Aug-2007 22:13:46, underclocker posted:

Hey @fastass - thanks for your quick reply! That was great.
Now I am thinking about how hot the stuff must be at the moment you put it into your ears. How do you heat it until it is ready and then put it in your ear? I've been reading about the stuff audiologists do and have formed opinions about open vs closed mouth etc.
One thing that head-fi.org users are doing wrong is ignoring the topic of headphone acoustics. You can widen or narrow the tube or even make or horn or bell as it reaches the end in your ear canal. I'd say straight or widening a bit would be the best. I see yours looks very constant from the pictures you posted. I see some head-fi users look like their opening narrows. If it narrows, I think that some frequencies would have a standing wave that would tend to dampen some frequencies. For monitors (as opposed to hearing aids) this would be bad. They comment that they have to EQ it so it sounds balanced but this nylon stuff sounds like it may give me a second chance if I mess up the drilling.
Where can one pick up the polymorph stuff at retail stores?

Comment on Create your own noise blocking in-ear headphones by fastass

Thu, 30 Aug 2007 14:30:12 -0500

At 30-Aug-2007 14:30:12, fastass posted:

Hi, underclocker, I attached the headphones by positioning them on the casts, with the holes allready made, and then covering them in strips of heated polymorph untill compleatly coverd. It doesnt need to be thick as it sets hard.You need the strips realy hot, I used a lit candle to heat them untill they go clear and you start to see them bubble, then cover over the headphones quickly bit by bit. The reason I heated the polymorph using a flame is beacause you need the strip to melt into the existing polymorph cast, using hot water doesnt let this happen.
Hope this answers your question. :)
I have been using my headphones everyday since making them with no problems at all and the casts have not lost there shape :) :)
Need anymore help, just ask ;)

Comment on Create your own noise blocking in-ear headphones by underclocker

Thu, 30 Aug 2007 14:03:13 -0500

At 30-Aug-2007 14:03:13, underclocker posted:

@fastass - I get it right until the finishing steps. How do you get your phones connected to the cast? Is there a reversable way to do that?

Comment on Create your own noise blocking in-ear headphones by fastass

Thu, 12 Jul 2007 02:24:11 -0500

At 12-Jul-2007 02:24:11, fastass posted:

This is one of the casts before trimmimg ect....
Shame U cant add multiple images to a comment :)

Any questions please ask :)

Comment on Create your own noise blocking in-ear headphones by fastass

Thu, 12 Jul 2007 02:22:29 -0500

At 12-Jul-2007 02:22:29, fastass posted:

Comment on Create your own noise blocking in-ear headphones by fastass

Thu, 12 Jul 2007 02:21:47 -0500

At 12-Jul-2007 02:21:47, fastass posted:

Comment on Create your own noise blocking in-ear headphones by fastass

Thu, 12 Jul 2007 02:20:58 -0500

At 12-Jul-2007 02:20:58, fastass posted:

Here are the pics

Comment on Create your own noise blocking in-ear headphones by natetrue

Tue, 10 Jul 2007 20:30:54 -0500

At 10-Jul-2007 20:30:54, natetrue posted:

I will have to get me some of that PolyMorph stuff. I just finished baking the wax off of my 'phones for a fresh coat of black paint to match my slick new iPhone. What do you think?

Comment on Create your own noise blocking in-ear headphones by fastass

Tue, 10 Jul 2007 15:22:02 -0500

At 10-Jul-2007 15:22:02, fastass posted:

Ive just finished them and they are fantastic. The molds are solid nylon and are rock hard, when you make the inital casting in your ear, you get the part that is shaped to your ear canal, in my case about 15mm, which you trim down, i was unable to bend it, it was that strong. The only dificulty is drilling which produces heat and causes a little softening, so i used a sioldering iron with a spoon bit to scoop out the mold !!!, to fit my Shure e3's into it. The only way they are going to melt is if they are dropped into boiling water, maybe left in the sun for hours on a very hot day or your ears catch on fire !!!!
I found the beauty of this stuff is that if you make a mistake you can melt a bit on or smooth the edges with heat rather than spend ages fileing away.
The result is a 1000% better sound performance than the sleeves they supply and what I expected !!!!.
As soon as I get the pics off the camera, i will post a link but need to get a card reader that works with XD cards, stupid camera LOL
OBTW......All credit to you for the instructions......THANKYOU

Comment on Create your own noise blocking in-ear headphones by natetrue

Tue, 10 Jul 2007 09:53:32 -0500

At 10-Jul-2007 09:53:32, natetrue posted:

That sounds like a great solution. Let me know how it turns out, I'm wondering whether the molds would start sagging over time.

Comment on Create your own noise blocking in-ear headphones by fastass

Tue, 10 Jul 2007 09:24:41 -0500

At 10-Jul-2007 09:24:41, fastass posted:

Great instructions but insted of using the epoxy putty ive used something called Pollymorph,

http://reprap.org/bin/view/Main/Polymorph

You can drill, sand, melt it and its smooth almost waxy to the touch and it sets in about 5 mins !!!
Will post some pics when I can !

Comment on Create your own noise blocking in-ear headphones by natetrue

Thu, 08 Feb 2007 12:15:04 -0600

At 08-Feb-2007 12:15:04, natetrue posted:

They're definitely a plus over normal earbuds. I'm not sure how they compare to over-the-ear headphones, especially the high-class ones, but the sound reproduction is excellent and I personally like how compact they are. If done properly you can sleep on them without noticing they're there at all.

Comment on Create your own noise blocking in-ear headphones by bigd

Thu, 08 Feb 2007 11:38:29 -0600

At 08-Feb-2007 11:38:29, bigd posted:

It's hard to say exactly how much they are truly attenuating without doing some physical measurements. Perceptions can be misleading. That being said, if you notice that you are significantly turning down the volume than with other headphones more power to you!

Comment on Create your own noise blocking in-ear headphones by natetrue

Thu, 08 Feb 2007 11:00:56 -0600

At 08-Feb-2007 11:00:56, natetrue posted:

Well, that depends on your definition of noise isolating. They block noise quite effectively (to my untrained ear, they knock off about 30-40 dB). At what level might you consider them to be "truly" noise-isolating?

Comment on Create your own noise blocking in-ear headphones by bigd

Thu, 08 Feb 2007 10:44:57 -0600

At 08-Feb-2007 10:44:57, bigd posted:

Are these truly noise-isolating? I think that with a dynamic speaker (like earbud style headphones) it wouldn't be. You would need to use a balanced armature receiver to have it truly noise-isolating.

Comment on Create your own noise blocking in-ear headphones by griff

Thu, 01 Feb 2007 10:59:13 -0600

At 01-Feb-2007 10:59:13, griff posted:

I'm a musician and was interested in trying this out in order to make in-ear monitors
for stage performance. You can buy something similar on line for about $900.
(http://www.ultimateears.com/custom/UE-10-Pro.htm)
This is considerably less expensive and the results are identical.

I only had one moment of terror.
"You'll feel your ear fuzz pulling out with a gently painful sensation. "
Apparently some of us have more ear fuzz than others. I had to exert a tremendous
amount of force in order to rip the fuzz out of my ears. Ow.
My new earbuds look like they're coated in blond velvet!

Aside from that arrrrrgh moment, they work very well. I mounted
a set of Koss buds and they sound very good -- Frequency response: 10Hz-20kHz
and very inexpensive: http://www.audio-discounters.com/spark-plug.html

If I did this again, I'd find some way to remove the fuzz from in and around the ear canal.
I'd also use plastic Q-tips and pack the epoxy around them that so its not necessary to drill
holes, just snip off the ends of the Q-tip.

Comment on Create your own noise blocking in-ear headphones by natetrue

Wed, 20 Dec 2006 10:57:19 -0600

At 20-Dec-2006 10:57:19, natetrue posted:

This just in - coat the molds (before drilling) with a thin layer of candle wax for a snugger fit. It also makes it easier to insert and remove them once they're complete.

You can also use minty scented wax for that minty fresh ear-scent!

Comment on Create your own noise blocking in-ear headphones by dwalk

Tue, 19 Dec 2006 17:38:39 -0600

At 19-Dec-2006 17:38:39, dwalk posted:

awesome, I really like the idea. I want to try to make these before Christmas with my dad. I also think the tip your audiologist gave about sticking a ball of cotton in your ear with some thread threaded through it. But make sure not to jam cotton balls in your ear too far either!

Comment on Create your own noise blocking in-ear headphones by jontempleton

Tue, 19 Dec 2006 09:40:36 -0600

At 19-Dec-2006 09:40:36, jontempleton posted:

This concept does work well. I've been using the little silicon "earplugs" that came with a jabra cell phone headset for this purpose, but they don't fit quite right. I've been thinking about doing something like this for a while, but I haven't found a good material . . . until now! Once you have these original earbuds made, you can then use them to make a mold using bondo, or some other hard substance that you can destroy later. Make lots of molds. Then if you ever lose or destroy these new earbuds you can make more easily using the molds. Plus, you can use other materials such as silicon or latex that may be more flexible, durable, more comfortable and has less chance of allergic reaction. You can also buld new earbuds with the headphones built right in for a seemless manufactured look. You have to include a small tube in your mold that you can remove later so you don't have to drill out the new earbud. Using the molds will give you a chance to try different things, practice and screw up a few times. But eventually, you'll have something that everyone else will envy. This is essentially the same process the pro's use. Cheap earphones will sound much better, but even slightly better earbuds will sound a lot better. I can't wait to do this myself!

Comment on Create your own noise blocking in-ear headphones by jesse

Mon, 18 Dec 2006 20:58:51 -0600

At 18-Dec-2006 20:58:51, jesse posted:

I beleive they should also conult their AUDIOLOGIST. And please PLEASE warn them not to put it too deep into their canal, the curve in many peoples earcanals CAN trap impression material and require surgery to have it removed...otherwise cool. AND set the impression on its back (with the canal pointing into the air) otherwise gravity may make it warp.